Brake Pads Complete With Sensor PRE-FITTED. Brake Disc Thickness [mm]: 12. For brake disc diameter [mm]: 282. Rear Brake Pads Complete With Fitting Kit.Kinetix Sports Performance Brake Discs. The key benefits of the dimpled and grooved discs are that brake fade is significantly reduced. The science behind this is the dimples and the grooves deglaze the pad and vents gasses that build up between disc and pad during braking. The additional slots dissipate heat more effectively, thus greatly reducing the risk of deformation, vibration or cracking of the disc at extreme operating temperatures. All Kinetix sports discs comes with Anti Corrosion Protection to prevent the discs from corrosion in areas not swept by the brake pad. Optimum brake performance is realised after the coating has been removed from the pad track area, which can take up to 100 miles. TRW Aftermarket DTEC brake pads.
DTEC is a premium quality, low dust brake pad with all the safety benefits of our main COTEC-coated range plus low dust technology to reduce rim surface dust levels on. Wheels by up to 45%. Low dust formulation for cleaner wheels. No compromise on safety performance.TRW rear and front brake pads offer more safety, wider coverage and easier fitting. Our new COTEC friction coating can cut the stopping distances on new brake pads by up to 7 metres so were making it standard and DTEC adds low dust to its safety performance. Plus, well give you all the fitting accessories you need to fit fast, and 98% coverage, so you can serve almost any vehicle. COTEC is a new friction coating developed by TRW that significantly improves safety after a brake pad replacement. The bedding-in process for brake pads normally begins with whats called a green behaviour period, when the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. Thats why we developed COTEC, to enhance the safety of our brake pads even further. COTEC-coated brake pads cut stopping distances by improving the contact between the brake pad and disc, and the results outperform both our major competitors and original equipment. The technology behind our brake pads and discs.
The back plate of the brake pad backed itself by the noise prevention shim is made from high quality steel and powder coated to reduce the development of rust. This robust plate is then bonded to the friction material with a unique adhesive compound that can withstand extremely high temperatures and shear strengths. And the scorched plate layer that follows is given an innovative surface coating that ensures optimised friction coefficient right from the first stop.
Brake pads that meet the standard. All our brake pads meet the strict ECE R90 specifications that other aftermarket brands have to meet. But for TRW the testing doesnt end there. We go further, adding shear strength testing during production control to ensure that the pad stays effective at any time. In short, TRW Aftermarket brake pads are tested to the extreme, both in the lab during production and on the road, just like original equipment pads, to meet industry standards.Then we test them harder, so that they meet our standards. Another way that we reduce the bedding-in time on replacement brake pads to a minimum is by applying an advanced plate scorching process to original equipment standards. We heat the brake pad material to 600-700°C by pressing the friction material onto a heated plate.
This heats the matrix of the friction material, allowing carbonization to occur to the first 0.5 to 1.5mm of its surface. This advanced scorching allows the evacuation of gases and resins, which are trapped inside the friction material at the mixing stage and its much more effective than conventional brake pad scorching techniques. Not all aftermarket suppliers scorch their plates to this advanced level and some dont even carry out the process at all. So, with TRW you can supply brake pads that offer both maximum safety and a more environmental product. The friction material is the most important part of the brake pad.Thats why we innovate, develop and manufacture so many components in-house, to make sure we can go on giving you the best possible quality. The ingredients of our material ensure a stable friction coefficient. They also ensure the safest braking performance in all temperatures, at all speeds and under all conditions. To achieve this, all our brake pads contain the optimum mix of raw materials from rubber to graphite. Less noise with TRW brake discs and pads. We work hard to eliminate noise and so TRW brake pads are fitted with high quality shims that act as a damper between the friction material and the brake caliper. And we use the same metal shim, held in place with special adhesive, thats used in original equipment. Our friction components are not only tested in our NVH (noise vibration harshness) laboratories but also on the road and we keep pushing the technology further. Were now using a fibre glass material instead of rubber for the shims of our aftermarket brake pads. We even produce integrally moulded shims and a multi-layer construction for the maximum noise reduction in our new brake pads. Outstanding service for car brakes and beyond. Well give you outstanding performance in braking technology, and customer service. That means wider coverage and easier fitting to keep your business moving, and better safety from new innovations such as COTEC and DTEC to keep your customers satisfied every time. TO FIT THE FOLLOWING VEHICLES. BEFORE PURCHASING WE RECOMMEND CONTACTING US WITH YOUR REG NUMBER or VIN NUMBER SO WE CAN CHECK FITMENT. THIS WILL AVOID ANY DISAPPOINTMENT OF. We make every effort to deliver goods within the estimated timescale. However delays are occasionally inevitable due to unforeseen circumstances.
We recommend you do not book your vehicle in for any repairs until you physically have the part to save on any disappointment caused by delays. Azcarparts Wakefield will be under no liability for any costs on damages or expenses caused by any delays. The item "FOR VW GOLF MK6 GTI FRONT REAR DIMPLED GROOVED BRAKE DISCS TRW PERFORMANCE PADS" is in sale since Wednesday, December 9, 2015. This item is in the category "Vehicle Parts & Accessories\Car Tuning & Styling\Performance Braking\Performance Brake Discs".The seller is "atozwakefield" and is located in Wakefield. This item can be shipped worldwide.